Some electrical problems make themselves known fast. A breaker that will not reset, an outlet that sparks, lights out in half the house. Those calls move to the front of the schedule. Others are slower: a panel that is getting close to capacity, wiring that needs updating before a renovation starts, a circuit that has been on the to-do list for months. We take both kinds of call, and we handle both the same way. You get a price on the phone before anything is booked, and the work is done to the standard the next inspection expects.
Johns Creek is a city with a wide range of housing. Newer subdivisions sit alongside homes that have been added to, renovated, and rewired in pieces over the years. Businesses and landlords with rental properties each have their own set of electrical needs, and the answer to most of them starts with the same call. We cover Johns Creek and the surrounding area every day from 6:30 AM to 9:00 PM.
Call (470) 749-3242 to describe the job and get a quote.
Calling an electrician doesn't have to be stressful, and the pricing conversation is a good example of why. When you call, we go over what the job involves, ask the questions that let us scope it accurately, and give you a rate before anything is put on the calendar. You know what the work covers before we arrive.
What moves a quote is the specifics of the job itself. The fault that turns up on a diagnostic visit may be at the outlet, at a GFCI upstream, at the breaker, or in the wiring behind the wall. Each of those is a different repair. Whether an existing circuit or panel can carry a new load, or whether the panel needs to be upgraded first, changes the scope. What has to be opened up to reach the problem changes it too. None of that is unusual, and none of it is a surprise when the job is scoped on the call.
Dead outlets, flickering lights, a burning smell near a switch, power missing from one part of the house. Each symptom points somewhere, and we trace it from the device back through the circuit to the panel. The diagnosis is explained before any repair begins. You hear what we found and what the fix involves before we touch anything.
A panel upgrade, a new dedicated circuit, or a service-entrance change all start with a load calculation. The panel needs to carry what is being added, and the quote reflects what that actually requires. If the scope changes once the panel cover comes off, that conversation happens on the spot before the work continues.
Dependable service. A price agreed before we start. Local know-how.
The schedule runs every day from 6:30 AM to 9:00 PM. When a problem will not keep, call and describe what is happening. A breaker that will not reset, a smell of burning near a panel, power out in part of the house. Those calls are treated as priority and we work to get to them as quickly as the schedule allows. There is no guarantee of a specific arrival window, but we do not leave urgent calls sitting.
For routine appointments, the call is how you book. Describe the job, get a price, and confirm a time that works. If a tenant is in the property, or if a business needs to stay open during the work, let us know on the call and we will work around the access requirements. Electrical service scheduled without the runaround is how every job starts.
Landlords and property managers often need the work coordinated with a tenant rather than handled directly. We are used to that. The scope and the price are settled with whoever is managing the job, the visit is arranged around the tenant's schedule, and the work gets done without the property sitting vacant waiting for a convenient window.
Commercial calls follow the same process. A retail space, an office, or a rental unit that has to stay open during the work gets the same scheduling conversation on the call. We confirm what access looks like and plan the visit accordingly. The specifics for a job like this are on our electrical services page.
For landlords and property managers, the paperwork side of an electrical job matters as much as the work itself. The invoice goes to whoever is paying for the job. If the work was done in a unit and the landlord needs a record of what was repaired or replaced, that is covered by what is documented on the visit.
Access arrangements are handled on the call. If the tenant is letting us in, we confirm that before the visit. If the property is vacant and a key needs to be arranged, that is part of the booking conversation. Nothing is assumed about access, and nothing is left to figure out on the day.
For a rental property, the scope of the work is agreed with the person who called, and any change to that scope is discussed before it happens. You do not get an invoice for work that was not authorized.
An inspection is the right first step when a property is changing hands, when a renovation has exposed wiring that looks uncertain, or when the panel has not been evaluated in a long time. We go through the panel, the wiring, grounding and bonding, GFCI and AFCI protection, and the condition of outlets and switches throughout the property. What we find is explained clearly, and any work that needs doing is scoped from there.
Older homes in Fulton County sometimes carry wiring that was installed when household electrical demand was far lower than it has become. Knob-and-tube wiring is ungrounded and was not designed for modern loads. Aluminum branch-circuit wiring can loosen at connections over time and creates a real risk at outlets and fixtures. Both are jobs we handle in full, running new copper wiring on the affected circuits and updating protection throughout. The scope and price are laid out before the work begins.
Ground-fault and arc-fault protection are required by code in kitchens, bathrooms, garages, and exterior locations, and older homes often do not have them in all the places they belong. An arc-fault breaker on a bedroom circuit, a GFCI outlet at the kitchen counter, a weatherproof exterior receptacle with proper protection. Each of these is a straightforward installation, and each one addresses a specific risk that the older wiring was never built to handle.
A staircase, a hallway, a large room with two entrances. Three-way switching lets you control a light from more than one location, and getting the wiring right is the part that matters. We handle new three-way installations and fix switching setups that were wired incorrectly the first time.
A dryer, a range, a refrigerator on its own circuit, or a Level 2 EV charger. Each of these needs a dedicated circuit sized to the load, and the panel needs capacity to carry it. We check the panel first, confirm whether an upgrade is needed, and run the circuit to where the appliance or charger will be. The visit covers the scope and the installation from start to finish.
Recessed lighting in a living room or kitchen, LED retrofits in a finished ceiling, under-cabinet lighting in a kitchen renovation. These jobs involve running circuits, cutting for new fixtures, and making sure the load is distributed correctly across the lighting circuits. We plan the layout before the work starts so the result matches what was agreed on the call.
Good electrical work isn't complicated, it's just done right, and lighting is where that shows most clearly. Inside, the difference between a room that feels finished and one that doesn't often comes down to where the fixtures are and whether the wiring was planned or improvised. Recessed lighting, ceiling fixtures, and under-cabinet lighting all require circuits routed cleanly through the ceiling or walls. When other work is already open, that is the right time to add lighting circuits rather than coming back later.
Outdoors, security lighting, motion sensor lights, and exterior outlets serve a practical purpose. A well-lit driveway, a back yard with a weatherproof outlet, a garage with proper exterior lighting. These are not decorative additions. They are part of what makes a property functional after dark, and the wiring is run to handle years of weather exposure. Local means we care what the neighbors think, and that applies to every exterior installation we leave behind.
Your time matters, so we keep the wiring job moving. If the visit is for a panel upgrade and the outdoor lighting circuit can be added at the same time, we scope both on the call so the decision is made before we arrive.
Quick response. Code-correct work. Tidy finish.
We take calls from across Johns Creek and the communities around it, including Berkeley Lake, Duluth, Alpharetta, Peachtree Corners, and Norcross. If you are in Fulton County or just across the county line, call and we will confirm whether the address is on the schedule.
We are available every day from 6:30 AM to 9:00 PM. Evening and weekend calls are welcome.
The work area is left clean and the panel is left labeled and covered. Any circuits added or modified are identified at the breaker. If the job involved a diagnostic, you receive a clear explanation of what was found, what was done, and whether anything else needs attention.
We let you know as soon as it becomes clear the work will not be finished in the original timeframe. The reason for the extension, the scope of what remains, and the updated price are all discussed before we continue. We do not add time to a job without explaining why.
In most cases, yes. Outlets, switches, covers, and fixtures come in a range of styles and finishes, and we can match what is already in the home in most standard configurations. If you have a specific product in mind, let us know before the visit so we can confirm it is compatible with the existing wiring.
Yes. On multi-day jobs, we restore power to the circuits that are safe to energize at the end of each working day. Circuits that are not yet complete stay off until the work on them is finished and tested. We confirm at the end of each day which circuits are live and which are not before we leave.
Yes. A welder and a large air compressor each draw enough current that they need a dedicated circuit sized to the equipment. Running either on a shared circuit is likely to trip the breaker and can cause voltage fluctuations that affect other equipment on the same panel. We size the circuit to the equipment's nameplate requirements before installing it.
An electrical issue that has been on the list for a while does not improve with time. A breaker that keeps tripping, a panel running close to capacity, wiring that has not been looked at since the last renovation. None of those fix themselves, and most of them get more involved the longer they sit.
We answer when you call. We explain the work. We leave it safe.
Call (470) 749-3242 and get a quote for the job you have been putting off. We take calls every day from 6:30 AM to 9:00 PM.
We also take electrical work in: Alpharetta, Peachtree Corners, Roswell. Browse our complete list of towns.
We handle the full range of electrical work for homes and businesses in Johns Creek and Fulton County, from a single dead outlet to a complete panel upgrade or rewire. Every job starts with a clear scope and a price confirmed before anything is scheduled. The table below covers what each service includes, who it fits best, and what is worth knowing before you call.
| Electrical Service | Scope of Work | Ideal For | What to Keep in Mind |
|---|---|---|---|
| Outlet & Switch Installation | New outlet and switch installation, GFCI and AFCI upgrades, Grounding and bonding corrections, USB and specialty outlet installation | Homeowners adding convenience or correcting code deficiencies | GFCI protection is required by code in kitchens, bathrooms, garages, and outdoor areas. We upgrade to current standards at the same time as the install. |
| Electrical Panel & Service UpgradesMost Popular | 200-amp service upgrades, Main panel replacement, Subpanel installation, Load calculation and service-entrance work | Older homes adding modern loads, EV chargers, or major appliances | Panel upgrades in Fulton County typically require a permit and inspection. We handle the permit side and make sure the work is ready when the inspector arrives. |
| Electrical Safety Inspections | Pre-purchase home evaluations, Post-renovation code checks, Failed inspection follow-up, Smoke and CO detector installation | Home buyers, sellers, and owners with older or unverified wiring | An inspection covers the panel, grounding and bonding, GFCI and AFCI protection, and the condition of outlets, switches, and fixtures throughout the property. |
Call (470) 749-3242 and we will go over the job, answer your questions, and give you a price before anything is scheduled.
(470) 749-3242