When a property manager gets a call from a tenant about a dead outlet or a tripping breaker, the job needs to move fast. Duluth carries a mix of residential properties, rental units, and commercial spaces, and the electrical calls that come in reflect that variety. A builder finishing a spec home needs circuits roughed in and panels sized correctly from the start. A landlord with a vacant unit needs a fault traced and cleared before the next tenant moves in. We handle all of it, and we take those calls every day from 6:30 AM to 9:00 PM.
Property types in Duluth range from newer subdivisions to homes that have been through multiple owners and multiple rounds of improvements. The electrical work we see reflects that range: panels that need replacing, circuits that were added without documentation, and wiring that has been modified over the years in ways that do not always meet current code. We scope the job on the call, confirm the price before anything is scheduled, and show up ready to work.
Not every electrical problem in a home or commercial space belongs to the property. Some faults originate on the utility side of the meter, and knowing where the line falls is the first step in any diagnosis. We start by checking what the panel is doing, whether the issue is limited to specific circuits or affects the whole property, and whether there are signs of a service entrance problem. If the panel is working and the incoming supply is not, that points to the utility.
If the fault is upstream of the meter, the utility company owns the repair. We will tell you that clearly rather than billing for work that is not ours to do. What we can do is document what we found, confirm the symptoms, and help you describe the problem accurately when you call them. If there is damage on the customer side of the meter that a utility event caused, such as a surge that took out a panel component, that repair is ours and we handle it from there.
Calling an electrician doesn't have to be stressful, and the scheduling conversation is a good example of why. When you call, we go over the job, ask what we need to know, and put a time on the calendar before you hang up. You do not wait for a callback to find out if you are on the schedule.
For problems that will not keep, we work with what the schedule allows and prioritize accordingly. A circuit that has gone dead in a commercial space, a panel fault that has taken out power to part of a building, or a safety concern that makes a property unlivable are all situations we treat differently from a routine installation. We are available every day from 6:30 AM to 9:00 PM, and that includes weekends.
Tenants and businesses that need to stay operational during the work are a regular part of the schedule. We discuss what needs to stay live, which circuits can be worked safely while others remain energized, and what the sequence of the job looks like before we start. The plan is settled before anyone shows up. Anything not covered here is on our electrical service list.
Homes of a certain age in this area were often built with knob-and-tube wiring. It is ungrounded, it was not designed for the loads a modern household runs, and it creates real limitations when insulation has been added around it or when circuits have been extended over the years without following the original system. It is not automatically an emergency, but it does need to be assessed. Where it is still in place and carrying load, replacement is the right answer. We run new copper wiring on the affected circuits, update GFCI and AFCI protection throughout, and confirm grounding before we leave.
Aluminum branch-circuit wiring shows up in properties built during a specific period and creates connection problems that develop over time. Aluminum expands and contracts differently from copper, and connections at outlets, switches, and fixtures can loosen in ways that generate heat and increase fire risk. The fix depends on how much aluminum wiring is present. Options include installing approved connectors at each device, replacing devices with aluminum-rated ones, or rewiring the affected circuits in copper. We assess the extent of the problem and explain the options before recommending either.
Good electrical work isn't complicated, it's just done right, and that applies as much to remediation work as it does to a new installation. Electrical work done to the standard the next inspection expects is the baseline for every job.
A finished electrical job is not just a repaired circuit or a new panel. It is a property that can be inspected, sold, or rented with confidence in what the wiring looks like. Every installation is tested before we leave: outlets checked for correct voltage and proper grounding, breakers confirmed seated and labeled, lighting circuits and fans run through a full cycle. If a panel was worked on, the load is verified against the breaker ratings before the cover goes back on.
Documentation matters when a property changes hands. A panel that is correctly labeled, with circuits identified and breakers sized to match, tells an inspector and a buyer's electrician that the work was done with care. We keep you informed from diagnosis to final test, and that includes walking through what was found, what was done, and what the property looks like electrically when the job is closed out.
Local permit rules decide which electrical jobs need an inspection. Where a permit is required, we handle that side and make sure the work is ready when the inspector arrives.
Your time matters, so we keep the wiring job moving, and that means being clear about what each type of job actually involves before we start.
A panel replacement is warranted when the existing box is too small for current loads, when breakers are failing or incorrectly sized, or when a renovation adds circuits the panel cannot support. We handle the full scope: panel removal, new panel installation, load calculation, and service entrance work where the incoming supply needs to match the new capacity. Subpanel installation for detached garages, workshops, or additions follows the same process.
Hardwired alarms are interconnected, so when one detects a problem, every unit in the home responds. That is a different level of protection from battery-only devices, and it is what code requires in most new construction and renovation work. We install the wiring, the devices, and the interconnect so the system functions as a whole rather than as individual units.
An outdoor outlet that is not properly protected fails quickly and creates a shock hazard in wet conditions. We install weatherproof GFCI receptacles and in-use covers that keep the outlet protected even with a cord plugged in. Exterior wiring is run in conduit where exposure requires it, and every outdoor circuit is tested for ground-fault protection before the job closes.
A welder or air compressor draws a load that a standard household circuit was not built to handle. Dedicated circuits sized to that load are installed alongside the correct outlet type, and the panel is checked for capacity before anything else in the shop or garage is affected. The load calculation happens before the circuit goes in.
Low-voltage work covers the rough-in for data lines, doorbell wiring, and structured cabling. We handle the rough-in side: running conduit, pulling cable, and confirming the pathway is clear for the equipment that follows. Where a doorbell transformer needs to be replaced or a new smart doorbell requires a different power supply, that is part of the same visit.
Recessed lighting and LED retrofits come up in both new construction and finished spaces. In a finished ceiling, the job involves identifying the right fixture for the space, confirming the circuit can carry the added load, and making the installation look clean from below. We handle the layout, the wiring, and the trim so the result reads as intentional rather than added on.
A Level 2 charger runs on a dedicated 240-volt circuit. We check the panel first, confirm available capacity, and install the circuit and outlet to the charger's specifications. Where the panel needs to be upgraded to support the charger, we scope both in the same conversation.
From older homes to new commercial builds, the price for electrical work is settled by what the job actually involves. The fault itself is one factor. What has to be opened up to reach it is another. Whether the existing circuit or panel can carry the change without modification is a third.
A straightforward outlet replacement is a different job from tracing a fault through a finished wall to find a loose connection three boxes back. A panel upgrade where the service entrance also needs work is a different scope from a panel swap where the incoming supply is already sized correctly. We go over all of that on the call so the price you hear reflects the actual job, not a best-case version of it.
We answer when you call. We explain the work. We leave it safe.
Call (470) 749-3242 and describe what you are dealing with.
The price is confirmed before anything is scheduled, and you are told what it covers.
We serve Duluth and the surrounding communities throughout Gwinnett County, including Berkeley Lake, Johns Creek, Peachtree Corners, Norcross, and Suwanee. If your address is just outside those areas, call and we will confirm whether it falls on the schedule.
We are available every day from 6:30 AM to 9:00 PM. Weekend and evening calls are welcome. Reach out and describe what the breaker is doing, or what the outlet is not doing, and we will take it from there.
Yes. We discuss which circuits need to stay live and which can be worked safely while the business operates, and we plan the sequence of the job around that before anyone arrives. The scope and the approach are settled on the call so there are no decisions being made on the fly once work begins.
Rental properties tend to generate calls about dead outlets, tripping breakers, and GFCI faults that a tenant cannot reset because the upstream device is in an unfamiliar location. Panels in older rental units sometimes have breakers that have been reset so many times they no longer hold reliably. We trace the fault, explain what caused it, and carry the repair through so the unit is ready for occupancy.
Yes. An intermittent fault is still a fault, and in many cases the underlying cause is more serious than a consistent problem because it points to a connection or component that is failing under specific conditions. Describing the pattern when you call, including when it happens and what triggers it, gives us the best chance of finding it on the first visit.
The attic does not need to be completely cleared, but we do need a clear path to the areas where the wiring runs. Stored items directly over the work area should be moved before we arrive. If the attic is heavily packed or has loose insulation that would need to be moved, let us know on the call so we can factor that into the visit.
It helps to know which unit or area is affected, what the symptom is, whether the problem appeared suddenly or has been building, and whether any previous electrical work has been done on that circuit or panel. If the property has multiple units and the fault is isolated to one, that narrows the diagnosis significantly and speeds up the call.
A warm or discolored outlet or switch cover is a sign of heat at the connection, which can result from a loose wire, a failing device, or a circuit that is carrying more load than it should. It is not something to leave in place. Call us and describe where the outlet is and what is typically plugged into it, and we will get it on the schedule.
Dependable service. A price agreed before we start. Local know-how.
If the electrical problem is in Duluth or anywhere in the surrounding Gwinnett County area, call (470) 749-3242.
We take calls every day from 6:30 AM to 9:00 PM. You get a real answer on the phone, a price before anything is scheduled, and no waiting for a callback that may or may not come. There are no forms and no queue.
We also take electrical work in: Johns Creek, Peachtree Corners, Alpharetta, Sugar Hill, Dunwoody. See the whole of our complete list of towns.
We handle the full range of electrical work for homes and businesses in Duluth and Gwinnett County, from a single dead outlet to a complete panel upgrade or rewire. Every job starts with a clear scope and a price confirmed before anything is scheduled. The table below covers what each service includes, who it fits best, and what is worth knowing before you call.
| Electrical Service | Scope of Work | Ideal For | What to Keep in Mind |
|---|---|---|---|
| Dedicated Appliance Circuits | Dryer and range circuits, Refrigerator and washer circuits, Workshop and garage circuits, Breaker sized to appliance load | Homeowners adding a major appliance or separating heavy loads from shared circuits | Running a dedicated circuit prevents nuisance tripping and protects both the appliance and the wiring feeding it. |
| Electrical Panel & Service UpgradesMost Popular | 200-amp service upgrades, Main panel replacement, Subpanel installation, Load calculation and service-entrance work | Older homes adding modern loads, EV chargers, or major appliances | Panel upgrades in Gwinnett County typically require a permit and inspection. We handle the permit side and make sure the work is ready when the inspector arrives. |
| Wiring & Circuit Installation | New circuit runs, 240V and 220V outlet installation, Whole-home rewiring, Knob-and-tube and aluminum wiring replacement | Older Duluth homes with outdated wiring or any property adding new circuits | Knob-and-tube wiring is ungrounded and was not designed for modern loads. Replacement is assessed circuit by circuit based on what is in place. |
Call (470) 749-3242 and we will go over the job, answer your questions, and give you a price before anything is scheduled.
(470) 749-3242